Patton CL1211

Patton_CL1212

The Patton CL1211 and CL1212 are Ethernet Extenders which use Patton’s classic form factor and run on their legacy 5VDC input.

The Patton CL1214, has a larger form factor, run on 12VDC and feature a built in 4 port switch.

The Patton CopperLink Model CL1211 can deliver IP traffic up to 1.8 miles (3 km) away—well beyond the standard 328-foot (100-meter) Ethernet distance limitation.

This is Patton’s single-port Ethernet Extender, ideal for applications requiring the enhanced security of a single Ethernet port.  With achievable line rates up to 168 Mbps, at shorter distances, the CL1211 eliminates the bandwidth constraints commonly experienced with other copper-based transmission technologies.

The Model 1211 is engineered to re-use existing infrastructure previously employed in such legacy applications as alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV. Many newer cabling standards are also supported, including Cat 5e, Cat 6 and Cat 7.

CL1211/EUI High Speed CopperLink Ethernet Extender; 1 x 10/100BaseTX; RJ45 Line, 100-240VAC

CL1211/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); 1 x 10/100BaseTX; RJ45 Line, 100-240VAC

CL1211/TB/EUI High Speed CopperLink Ethernet Extender; 1 x 10/100BaseTX; Terminal Block Line, 100-240VAC

CL1211E/EUI-2PK Extended Temperature CopperLink High Speed Auto Rate Extender Kit (Local and Remote); 1 x 10/100BaseTX; RJ45 Line Connector; 100-240VAC

CL1211E/TB/EUI-2PK Extended Temperature CopperLink High Speed Auto Rate Extender Kit (Local and Remote); 1 x 10/100BaseTX; Terminal Block Line Connector; 100-240VAC

CL1211E/TB-SKD Ethernet Extender, PCB Sub Assembly, Terminal Block Line; 1 x 10/100; No Power Supply

CL1211E-SKD Ethernet Extender, PCB Sub Assembly, RJ45 Line; 1 x 10/100; No Power Supply

CopperLink Line Interface
  • RJ-45 (pin 4 = ring; pin 5 = tip)
  • Terminal block, 2 position
CopperLink Line ModulationDMT (Discrete Multi-Tone)
Ethernet Interface8-position, shielded RJ-45. Auto-sensing 10/100Base-TX with half or full duplex operation.  Model 1211 has one 10/100Base-TX port.
ProtocolTransparent to high layer protocols: supports 802.1Q VLAN tagged or untagged frames.
Transparent to IP Video schemes: fully transparent to such compression schemes as MPEG-4, H.264, and MJPEG.
Target SNR Modes6 dB and 9 dB
Management8-position DIP switch
Monitoring8 LEDs display Power, Link, Ethernet 1–4, Remote, and Local status.
Power SupplyExternal AC: 100–240 VAC
ComplianceFCC Part 15A, CE Mark, EMC Directive 89/336/EEC, Low-Voltage Directive 73/23/EEC
Environment
  • Temperature: 0 to 50°C
  • Humidity: 5 to 95%, non-condensing
  • Extended Temperature: -40 to 85°C ( CL1212E or CL1211E)
  • Extended Humidity: 5 to 85%, condensing (CL1212E/CC or CL1211E/CC)
Dimensions4.13 W x 1.5 H x 3.15 D in. (105 W x 38.1 H x 95.3 D mm)
Weight0.4 lbs (181 g)
MTBF77,000 hours

Patton 552-GS2 Surge Protector

Patton_552_Surge

Your telco lines are a vital data link with the outside world. But they can also end up bringing some very undesirable transient spikes into your data ports.

The Patton Model 552 installs between an incoming telco line and dial-up/leased line/xDSL modem, ISDN modem (a.k.a. TA or NTU), T1/E1/PRI or DDS and intercepts harmful telco line transients before they cause hardware damage. Surge energy is then diverted to nearby chassis ground through a braided metal strap.

Model 552-D2 (dial-up line) protects RJ-11 pins 3 & 4
Model 552-D4 (dual dial-up line) protects RJ-11 pins 2, 3, 4 & 5
Model 552-DDS protects RJ-45 pins 1, 2, 7 & 8
Model 552-T1 (T1, E1, PRI) protects RJ-45 pins 1, 2, 4 & 5
Model 552/U protects pins 3, 4, 5 & 6 on the RJ-45 connector
Model 552-ST (ISDN) protects all 8 RJ-45 pins. The ISDN versions of the Model 552 protect both data and battery signals.
Model 552-GS2 protects RJ-45 pins 4 & 5, whereas the 552-GS4 protects RJ-45 pins 3,4,5 & 6.

The G.SHDSL versions of the Model 552 have a surge handling capacity of 600W, all other versions can handle surges of 1500 Watts. A 6-inch (15-cm) adapter cable is supplied with all Model 552 versions.

These are also very effective surge suppressors for Ethernet Extenders

Surge Protectors

Patton Line Protection for Serial
Dial Leased DSL T1 PoE &  Ethernet Extenders

Patton_Surge_Protectors

Spikes can also occur on telephone and data lines when AC (alternating current) main lines accidentally connect to them or lightning hits them or the telephone and data lines travel near lines with a spike and the voltage is induced.  Here are some surge protection devices from Patton Electronics to protect various data communcations and networking devices.

509/25 DB-9 TO DB-9 SURGE SUPPRESSOR RS232
509/6 DB-9 TO DB-9 SURGE SUPPRESSOR RS422 RS485
552-D2 2-WIRE DIAL UP SURGE PROTECTOR
552-D4  4-WIRE LEASED LINE PROTECTOR
552-E1 4-WIRE E1 SURGE PROTECTOR
552-E1   4-WIRE E1 COAX PROTECTOR
552-GS2  2-WIRE G.SHDSL SURGE PROTECTOR
552-GS4  4-WIRE G.SHDSL SURGE PROTECTOR
552-L4  4-WIRE LEASED SURGE PROTECTOR
552-L8  8-WIRE LEASED LINE PROTECTOR
552-ST  ISDN SURGE PROTECTOR
552-T1  4-WIRE T1 PROTECTOR
570  10/100 BASE-TX SURGE PROTECTOR
570-POE  10/100BASE-TX 802.3AF POWER OVER ETHERNET SURGE PROTECTOR
591AF  RS-232 TO RS-232 OPTO ISOLATOR


You can always call for a quick quote.
If you like the price, you can order right over the phone.