|
CopperLink-T T1
Extender
- Triple the Distance--Extend T1s to over 3 miles and E1s to
almost 5 km over one pair of wires.
- Half the Wires--The T1 extenders only require one pair of
wires to operate.
- Voice and Data Extension--The T1 Extenders operate in clear
channel mode allowing the transparent passing of both voice and
data.
- Plug and Play--Plug them in and the link comes up in seconds.
The line interface is even polarity insensitive, making it
easier to get running.
- Line Tests--V.52 511/511E Pattern Generator with Remote
Digital Loopback (RDL); Local Analogue Loopback (LAL).
- Front Panel Status Indicators--Front Panel LED’s provide users
with quick feedback on unit operation.
The
Patton 2115 T1 Extenders are the perfect choice for enterprises,
integrators, and service providers needing to extend T1 and E1
circuits beyond their typical reach while conserving the number of
wire pairs used.
With the CopperLink™-T extenders, zero configuration is required.
They operate in clear-channel mode, thereby facilitating the
transparent extension of data and voice bearing circuits—including
the F-bit on T1 circuits. The two active pins on the RJ connector
are polarity insensitive, so you don’t even need to worry about
which wire you connect on the line interface. Simply take them out
of the box, put them on either side of the dry copper pair, connect
your T1 or E1 device and the circuit will light up immediately!
The Patton 2113 extends E1 circuits to 16,100 feet (4,900 meters,
nearly 5 km) while the Patton 2115 extends T1 circuits to more than
3.5 miles (18,500 feet or 5,600 meters). Both models require only
two wires (one pair) to extend the TDM circuits, thereby conserving
and minimizing the copper plant resources used.
For these reason, the CopperLink™-T extenders are the ideal solution
for most popular applications such as T1/E1 backhaul from a remote
site, T1/E1 relocation, T1/E1 extension across a campus or between
buildings, and last-mile TDM delivery.
- The CopperLink™-T simplifies transparent T1 extension.
- Plug-and-Play--units automatically link up when placed on
opposite sides of a dry copper wire pair.
- Units operate in clear channel mode to easily transport voice
and data (F-bit included).
- Uses only wires on the link.
- Link interface is polarity insensitive to make connection to
the twisted-pair wires easy.
- Intuitive LEDs help you quickly troubleshoot line and circuit
problems.
Patton 2115 T1 Extender: Single female RJ-48C
Supported Line Tests: V.52 511/511E Pattern Generator with
RDL; LAL
Clocking: CO unit preset for Network Clock, CPE unit preset
for Receive Recover
Line Coding: 16-constellation TC-PAM
Line Interface: Female RJ-11 using pins 2 & 3; Two wires
(single twisted-pair)
Front Panel Indicators: Power--Solid green indicates
unit is powered up. Slow blinking indicates unit is in POST. Fast
blinking indicates unit failed POST. Dark indicates unit does not
have power.
Link--Solid green indicates end-to-end link. Flashing
indicates unit is training. Dark indicates link is down.
Frame--Solid green indicates valid framing. Flashing
indicates signal being received, but no link established.
Power Supply: External power supply options: Universal 90–260
VAC operating from 50–60 Hz; 120 VAC/60 Hz; 240 VAC/60Hz; -48 VDC
Compliance: FCC Part 15A, CE Mark, EMC Directive 89/336/EEC,
Low-Voltage Directive 73/23/EEC
Environment: Operating Temp.: 32–122°F (0–50°C)
Humidity: 5–90% non-condensing
Dimensions: 4.7 x 1.52 x 5.0 in. (10.6 x 3.9 x 12.7 cm)
2115/EUI-2PK
CopperLink-T T1 Extender, 2 pack
Patton 2115 Manual PDF |
