T1 Extender T Extenders T-Extenders

Data Connect Copper-T
T1 Extender T Extenders T-Extender

Copper-T Data Sheet

The Data Connect Copper-T is a T1 demarc extension device or T1 repeater. This simple unit allows T1 DSUs, channel banks, routers, and PBXs to be located up to 5000 feet from the telephone company's demarc. With T1 lines becoming more common in the business and school environment, this is a lifesaver in campus and high-rise environments. The Data Connect Copper-T is powered by a small wall-mount transformer or optional DC power supply, and is used for connections between T-1 equipment such as PBXs, telco demarcs, T-1 multiplexers, T-1 line drivers, T-1 local multiplexers or any other T-1 equipment requiring long customer owned cable runs. Data Connect Copper-Ts can be used to connect this equipment across a campus, between floors of a high-rise office building or between office buildings with underground cable connections.

T-1 4-wire repeater
Extends in-house T-1 lines
Up to 5000 feet between units (depending upon cable)
RJ-45 or screw down connectors
Simple connection to a 4-wire line
Inexpensive solution to long T-1 runs
120VAC, 48VDC, or 24VDC powered

RJ-45 adapter or screw terminals may be used in either or both ports. Unit supplied with two screw terminals and one RJ-45 adapter.

The Data Connect Copper-T is a 4-wire T-1 repeater for use on customer owned lines. The Data Connect Copper-T is used to extend in-house T-1 lines in campus and high-rise environments.

Note: This product is NOT intended for 10BaseT or Ethernet. T1 modulation is designed for use with twisted pair solid wire phone cables. The Data Connect Copper-T does NOT extend ethernet connections... only T1 connections. For Ethernet Extenders go here.

Each pair of Data Connect Copper-Ts may be located up to 5000 feet apart. Solid copper 22 AWG two twisted pair is the preferred cable for connection between Data Connect Copper-Ts. Smaller wire sizes will reduce the functional distance between Data Connect Copper-Ts. Connection to the Data Connect Copper-T is made through RJ-45 modular connectors or 4-wire screw down barrier strips. Both types of connectors are standard on the Data Connect Copper-T.

The Data Connect Copper-T is powered by a small wall-mount transformer, and is used for connections between T-1 equipment such as PBXs, T-1 multiplexers, T-1 line drivers, T-1 local multiplexers or any other T-1 equipment requiring long customer owned cable runs. Data Connect Copper-Ts can be used to connect this equipment across a campus, between floors of a high-rise office building or between office buildings with underground cable connections.

Data Connect Copper-Ts can also be used to extend the distance between any T-1 equipment (DSU, channel bank, router, etc.).

The Data Connect Copper-Ts are best used in pairs. If you have a T1 CSU that is limited to 655 feet, connected to a device limited to 655 feet, and you put the Data Connect Copper-T at one end, the Data Connect Copper-T will drive the extra distance. However, the far end device will still be limited to 655 feet and will not likely have sufficient "drive" to reach the far end. The T1 transmitted signal is the issue addressed by the Data Connect Copper-T, so in this case, the line would be error-prone or possibly only work in one direction.

Data Connect Copper-T	T-1 Line repeater for up to 5000 feet
9500095	Customer to demarc RJ45 cable
9500099	Customer to customer T1 RJ45 crossover cable
9502122	Additional RJ adapter
5003011	Additional screw terminal adapter
9902095	19" rack shelf for 1 to 3 Data Connect Copper-Ts

NOTE : Cable should be Category 3, 2 twisted pair, shielded.
DO NOT use Category 5 cable.
Proper operation cannot be guaranteed if Category 5 cable is used.

Using CAT5 or CAT6, the transmit and receive pairs are not shielded from each other, making
Near End Cross Talk likely. If you can use 2 separate cables of CAT5 or CAT6, putting the TX pair in one and the RX pair in another, that would help greatly. The key, is proper sheilding of the pairs.

If this is an issue in your application,
or if you need to extend your T1 greater distances,
we recommend a different product:
Patton 2115 T1 Extender

Extender Products

Patton 2115 T1 Extender

Fiber T1 Extender